Ugh.. Anyone good with electrical? I have a light bar with 2 kc lights and an internal switch. My lights aren't working anymore.
Looking for help?
2 kc lights not working
- ASauer17
- BSJ BOD President
- Posts: 3151
- Joined: Fri Apr 08, 2011 12:32 pm
- Jeep Year: 1998
- Jeep Model: TJ Wrangler
- Real Name: Amanda
- Location: Hubbardston ma
2 kc lights not working
98/99 TJ
2025 President
----------------------------------------
2023 & 2024 President
2021 Director of Events
2018 Secretary
2016 & 2017 President
2014 & 2015 Secretary
2025 President
----------------------------------------
2023 & 2024 President
2021 Director of Events
2018 Secretary
2016 & 2017 President
2014 & 2015 Secretary
-
- BSJ 101 Planning Commitee
- Posts: 57
- Joined: Tue May 19, 2015 11:13 am
- Jeep Year: 2014
- Jeep Model: JK Wrangler
- Location: Whitman
Re: 2 kc lights not working
Both lights aren't working? Do you have an inline fuse from the switch to the lights? If so, check that fuse first. If not, where's the switch mounted? You'll have to get to the blades on the back and test for power with a multimeter before moving forward.
He who seeks darkness where there is light, seeks evil.
- ASauer17
- BSJ BOD President
- Posts: 3151
- Joined: Fri Apr 08, 2011 12:32 pm
- Jeep Year: 1998
- Jeep Model: TJ Wrangler
- Real Name: Amanda
- Location: Hubbardston ma
Re: 2 kc lights not working
Both. Idk what happened!!
98/99 TJ
2025 President
----------------------------------------
2023 & 2024 President
2021 Director of Events
2018 Secretary
2016 & 2017 President
2014 & 2015 Secretary
2025 President
----------------------------------------
2023 & 2024 President
2021 Director of Events
2018 Secretary
2016 & 2017 President
2014 & 2015 Secretary
-
- BSJ 101 Planning Commitee
- Posts: 57
- Joined: Tue May 19, 2015 11:13 am
- Jeep Year: 2014
- Jeep Model: JK Wrangler
- Location: Whitman
Re: 2 kc lights not working
Do you have it wired with a relay? If so, there should be an inline fuse on the main HD battery cable and also on a smaller gauge wire that runs to the switch. Check both of those first. My experience has seen the smaller gauge wire fuse fail since it's prob just a 10 amp. If you dont have a relay and it's direct wired from the battery to the back of the switch, then you'll need to grab multimeter, put it to DC, put the switch "on", and check both sides for roughly 12v. Even without a relay, you should still have an inline fuse close to the battery so, again, check that first. If you're hot on both sides of your switch, chances are wherever the junction is where the 3 wires (Power and both light feeds) come together has an issue. I solder all my connections but most ppl crimp the wires without some sort of weather seal and it eventually fails. Keep me posted.
He who seeks darkness where there is light, seeks evil.
- Kurt
- BSJ Member
- Posts: 4209
- Joined: Wed Dec 23, 2009 11:53 am
- Jeep Year: 1992
- Jeep Model: YJ Wrangler
- Real Name: Kurt K.
- Location: Pepperell, MA
Re: 2 kc lights not working
Bring it to Ralph's wrenchfest and we'll get it fixed for you.
"Build It, Run It, Break It, Improve It, Repeat!"
NEA Treasurer 2016, 2017, 2018, 2019, 2020
BSJ Treasurer 2020
NEA Treasurer 2016, 2017, 2018, 2019, 2020
BSJ Treasurer 2020