Baystate Jeepers

Posted: **Wed Mar 18, 2015 8:14 am**

Voodoo Chile wrote:
Posimoto wrote:I'm curious if you talked to them and presented pics, if so what was their response?

he accused me of not breaking the R&P in properly. _ I did stopping several times for cool down on the drive home and it was fouled diff fluid due to off road use. there were a chit load of metal flakes that were either from before the swap or a bad setup. Its working OK several years later but he does not stand behind the work he just did and never was able to send me a pattern which I requested. the slap em together and call it good without documenting much. Im sure they would either a) remember Ryan and say look at the abuse to your Jeep or b) outright ignore him. #vendorFail

Jeff, thanks for the reply. You called for a good reason, because you broke in the gears correctly. If a customer has a complaint it should be addressed. But at the end of the day, in your case with the break-in, it's a he said, she said. For business sake he should have took care of you.

Ryan has a different situation and has great support for his argument. I'm AWS certified welder and pics don't lie. I'd be looking for a refund or parts in exchange for poor workmanship. If Ryan doesn't contact him maybe the worker who welded his axle is still working there, if he is still working there maybe he is still pushing out poopy welds. If Mitchells doesn't respond, or blows it off, it would add a lot of weight behind this thread. Just saying.

Posted: **Sat Mar 21, 2015 7:06 am**

Posimoto wrote:I'm thinking your not addressing my post because nothing you posted has anything to do with my question, but I figured I'd ask because I wasn't sure.

I have had issues with them in a shop to shop setting and returned for re-work and spoken to them and sat in on conference calls with them about the problems, plural, and in the end the one shop decided not to do business with them again. I was involved in repairing their work several times and wrote a statement as a witness in a law suit they lost.

Each conversation included the words, "This has never happened before."

On the flip side, I bought a used D30HP 3.73+ carrier from them and a Yukon D35 side gear kit for a non C Clip axle and the sales service was great, low prices, too.

Posted: **Sat Mar 21, 2015 7:11 am**

Posimoto wrote: Jeff, thanks for the reply. You called for a good reason, because you broke in the gears correctly. If a customer has a complaint it should be addressed. But at the end of the day, in your case with the break-in, it's a he said, she said. For business sake he should have took care of you.

Ryan has a different situation and has great support for his argument. I'm AWS certified welder and pics don't lie. I'd be looking for a refund or parts in exchange for poor workmanship. If Ryan doesn't contact him maybe the worker who welded his axle is still working there, if he is still working there maybe he is still pushing out ****** welds. If Mitchells doesn't respond, or blows it off, it would add a lot of weight behind this thread. Just saying.

Well said and good point.

Posted: **Thu Mar 26, 2015 11:52 pm**

Quick update. I decide to email Dan at Mitchell for the hell of it, just to see what sort of response I would get. So far, one week later, crickets. I didn't ask him to "take care of me" or anything, but I would still expect some sort of reply thanking me for letting him know. I guess there's a small chance my email went into his spam folder since I had the two pics attached, but they are pretty small pics. And no, his reply back to me is not in my spam folder, I checked

Posted: **Sat Mar 28, 2015 7:16 am**

Disappointing, more folks should know about this.
He will never have my business again.

Posted: **Thu Apr 09, 2015 10:48 am**

And here's the response I just received... " Morning Ryan, Sorry for the delayed response. That is breakage is very unusual. We've built hundreds of those units & this would be the first one I've seen broken. Did you hit something? Dan"

Posted: **Thu Apr 09, 2015 12:38 pm**

You should reply.

"No I did not hit anything. Like all Jeepers my Jeep is either stored in a climate controlled garage or sitting in a mall parking lot."

Posted: **Thu Apr 09, 2015 12:40 pm**

On a serious note they are a major distributor for Yukon Gear and Axle, I would let them know about the customer service you are getting. I can give you the direct email of their director of marking.

Posted: **Sun Apr 12, 2015 10:33 pm**

It's tempting... I don't want to "destroy" Mitchell, but I also want to make sure others know what they are getting themselves into if they decide to do business there. I don't see Mitchell changing their ways, no matter what any of us do.

Posted: **Mon Apr 13, 2015 7:42 pm**

I know another BSJ ex-member who bought from Mitchell, had parts fail, and got nothing from them. Don't hold back on them Ryan... You're the 4th person I know who has had quality problems just in BSJ.

Posted: **Tue Apr 14, 2015 5:51 am**

Baseshakers wrote:It's tempting... I don't want to "destroy" Mitchell, but I also want to make sure others know what they are getting themselves into if they decide to do business there. I don't see Mitchell changing their ways, no matter what any of us do.

My fear is really for the newbie that goes in and has these amateurs do work for them, never checks the fluid after the work is done and destroys a r&p or locker because Mitchell didn't set it up correctly... or clean the diff well enough after a breakage -which is my best guess as to how the screwed mine up. the ARB seems OK over a year later despite the extensive sludge and fines I found before wheeling it and after they did the work.

On my way home, I stopped and let the jeep cool down 3x on the way from Shrewsbury to Westford which is under 50 miles so I am certain it was nothing I did wrong...

Wont ever spend a dime there again or even consider asking them for anything for CFAC.... :teasing-knob:

Posted: **Sat Dec 09, 2017 3:45 pm**

Finally got around to one of my winter projects repairing the front truss which broke off completely. Flipped it over to weld in a plate to brace the corners and look what I found... another sh1tty weld from Mitchell. (FYI outer surface was already ground down flat by me prepping for the plate). 25% penetration, maybe? No bevel for the weld, and they didn’t even attempt to weld the inside. Pitiful workmanship.

Posted: **Mon Dec 11, 2017 7:59 am**

A good way to repair that would be running a thin cutoff wheel the length of the crack for internal stress relief and penetration. Find the end of the crack and drill a small hole below it before you cut it and go to that hole. No Charge Bud. FjR68

Baystate Jeepers

Mitchell Differential

Re: Mitchell Differential

Re: Mitchell Differential

Re: Mitchell Differential

Re: Mitchell Differential

Re: Mitchell Differential

Re: Mitchell Differential

Re: Mitchell Differential

Re: Mitchell Differential

Re: Mitchell Differential

Re: Mitchell Differential

Re: Mitchell Differential

Mitchell Differential

Re: Mitchell Differential