It has been so long since I have wrenched on the jeep and I can't remember the torque spec replacing a yoke for an HP D30. I could pull the carrier and go the hard route, but I have to imagine there is an easier route?
Does 210 FT LB sound correct?
replacing HP D30 yoke toque?
-
ChrisD
- BSJ 101 Planning Commitee
- Posts: 1791
- Joined: Wed Dec 23, 2009 12:53 pm
- Jeep Year: 2003
- Jeep Model: TJ Wrangler
- Real Name: Chris
- Location: Westminster, Ma
Re: replacing HP D30 yoke toque?
Anyone?
-
BlackNBlue-ISH
- BSJ Member
- Posts: 1824
- Joined: Mon Mar 24, 2014 12:25 pm
- Jeep Year: 2005
- Jeep Model: TJ Wrangler
- Real Name: Daniel or "ish"
- Location: Manchester, NH
Re: replacing HP D30 yoke toque?
My cheat sheet of torque values has "???" as axle Yoke Nut torque. At the transfer case it's 110-120 ftlbs.
If I recall, you may not be far off though.
If I recall, you may not be far off though.
2005 TJ, built and beat accordingly
-
BlackNBlue-ISH
- BSJ Member
- Posts: 1824
- Joined: Mon Mar 24, 2014 12:25 pm
- Jeep Year: 2005
- Jeep Model: TJ Wrangler
- Real Name: Daniel or "ish"
- Location: Manchester, NH
Re: replacing HP D30 yoke toque?
For the TJ D30 (low pinion) per the service manual, the pinion nut torque spec is 160-200 ft lbs. 
2005 TJ, built and beat accordingly
-
MDSRACING398
- BSJ 101 Planning Commitee
- Posts: 3294
- Joined: Fri Feb 12, 2016 10:24 pm
- Jeep Year: 1985
- Jeep Model: CJ7
- Real Name: Mark
Re: replacing HP D30 yoke toque?
Just re read you said hp30. If reusing nut couple drops of red lock tight 180 will do you fine.
Do it right the first time!
Second place is First Loser! Work Harder
Semper Fi
Second place is First Loser! Work Harder
Semper Fi
-
ChrisD
- BSJ 101 Planning Commitee
- Posts: 1791
- Joined: Wed Dec 23, 2009 12:53 pm
- Jeep Year: 2003
- Jeep Model: TJ Wrangler
- Real Name: Chris
- Location: Westminster, Ma
Re: replacing HP D30 yoke toque?
Big thanks!
-
Frank
- Frankie BSJ Member
- Posts: 4145
- Joined: Sun Dec 27, 2009 8:54 am
- Jeep Year: 1974
- Jeep Model: CJ5
Re: replacing HP D30 yoke toque?
I thought the big difference was one had a crush sleeve , not to be reused and the other had bearing and shims. That would be the biggest torque difference between the two. FjR68
-
nhdcoye
- BSJ Member
- Posts: 932
- Joined: Wed Jan 06, 2010 9:04 pm
- Jeep Year: 1992
- Jeep Model: YJ Wrangler
- Real Name: Better known as Dave
Re: replacing HP D30 yoke toque?
Actually I thought the Dana 30 could not take any torqueFrank wrote:I thought the big difference was one had a crush sleeve , not to be reused and the other had bearing and shims. That would be the biggest torque difference between the two. FjR68
92 YJ 6Cyl > 3 " lift, ford 8.8 SOA on XJ springs with Aussie out back, D30 with alloy 30's and ARB up front 4:56. 35 MTR's, 10K Winch, SYE ,traction bar, onBd Air and lots of gently used skids