Code PO 306

Jeepster2586
BSJ 101 Planning Commitee
Posts: 12
Joined: Sun Mar 19, 2017 7:38 am
Jeep Year: 1997
Jeep Model: TJ Wrangler
Real Name: Mike D.

Code PO 306

Unread post by Jeepster2586 »

My 1997 TJ with a 4.0 starting running rough and the check engine light came on. I pulled the codes and I have a PO 306. Which is a misfire on cylinder 6.
Here is what I checked.
Spark....good.

Noid light check on injector wiring.....light flashes. Wiring to injector seems ok.

Full compression check on all cylinders. Each one was right about 150. The gauge seemed to climb steadily on each cylinder. I don't think there is any major engine problem.

I decided it probably has a bad injector. I changed the injector on number 6. Problem is still there.

What am I missing.....any ideas?
Jeepster2586
BSJ 101 Planning Commitee
Posts: 12
Joined: Sun Mar 19, 2017 7:38 am
Jeep Year: 1997
Jeep Model: TJ Wrangler
Real Name: Mike D.

Re: Code PO 306

Unread post by Jeepster2586 »

Also I went along the wiring for each injector removing the connector while it was running . Cylinder 6 was the only connector that made no change when unplugged. That was the reason I changed the injector.
User avatar
Kurt
BSJ Member
Posts: 4207
Joined: Wed Dec 23, 2009 11:53 am
Jeep Year: 1992
Jeep Model: YJ Wrangler
Real Name: Kurt K.
Location: Pepperell, MA

Re: Code PO 306

Unread post by Kurt »

Possibly a wiring issue between the PCM and the injector.
If you have a meter you could check for proper continuity between the two.
"Build It, Run It, Break It, Improve It, Repeat!"
NEA Treasurer 2016, 2017, 2018, 2019, 2020
BSJ Treasurer 2020
Jeepster2586
BSJ 101 Planning Commitee
Posts: 12
Joined: Sun Mar 19, 2017 7:38 am
Jeep Year: 1997
Jeep Model: TJ Wrangler
Real Name: Mike D.

Re: Code PO 306

Unread post by Jeepster2586 »

The weird thing is that if I plug in the noid injector tester the light flashes which means the wiring/ pulse from the PCM is valid...I think???? I also plugged it into every other injector wire and it appears that all cylinders are receiving pulses from the PCM.
User avatar
MDSRACING398
BSJ 101 Planning Commitee
Posts: 3294
Joined: Fri Feb 12, 2016 10:24 pm
Jeep Year: 1985
Jeep Model: CJ7
Real Name: Mark

Re: Code PO 306

Unread post by MDSRACING398 »

Make sure exhaust manifold didn't crack. Also cam positioning sensor can cause misfire codes. Could of got bad injector too. Can do the old swap injectors on cylinders and see if code moves to other cylinder.
Do it right the first time!
Second place is First Loser! Work Harder
Semper Fi
User avatar
Kurt
BSJ Member
Posts: 4207
Joined: Wed Dec 23, 2009 11:53 am
Jeep Year: 1992
Jeep Model: YJ Wrangler
Real Name: Kurt K.
Location: Pepperell, MA

Re: Code PO 306

Unread post by Kurt »

You could have a bad spark plug.
I've seen them fail causing a cylinder to cease firing even though they look "good".
Might try swapping spark plugs around and see if the problem moves cylinders.
"Build It, Run It, Break It, Improve It, Repeat!"
NEA Treasurer 2016, 2017, 2018, 2019, 2020
BSJ Treasurer 2020
Jeepster2586
BSJ 101 Planning Commitee
Posts: 12
Joined: Sun Mar 19, 2017 7:38 am
Jeep Year: 1997
Jeep Model: TJ Wrangler
Real Name: Mike D.

Re: Code PO 306

Unread post by Jeepster2586 »

I replaced all the spark plugs. No change. I guess I am going to try spraying brake kleen around the intake manifold while its running to see if that changes the RPM. I will swap the injectors around and see what happens.

Can a cam sensor cause only one cylinder to misfire? What about the crank sensor? Would that do a single cylinder misfire?

Also I'm going to do a vacuum test just to rule that out.
Post Reply